Textile Mills & FibersTKT-1EFA

Bangladesh trial cuts CVC dyeing steam use 16.7% at 115°C

A NAZ Bangladesh trial dyed 80/20 CVC single jersey at 115°C instead of 130°C, cutting steam use 16.7% and process time by 52 minutes per batch while holding rubbing fastness grades.

Cut
November 17, 2026
Sew
4 min
Ticket
TKT-1EFA
An energy and steam saving alternative to conventional high-temperature polyester dyeing
An energy and steam saving alternative to conventional high-temperature polyester dyeingOfotoRay / pixabay

Construction

  1. Carrier-assisted dyeing at 115°C cut steam use 16.7%, from 1.286 to 1.072 kg steam per kg fabric, against a 130°C baseline.

  2. Total dyeing time fell from 222 to 170 minutes per batch, a calculated 23.4% productivity gain.

  3. Trial ran at NAZ Bangladesh Ltd on 42 kg of 80/20 CVC single jersey, GSM 180, commissioned by HI TECH with Transfar Chemicals' TF-258WH carrier.

  4. Rubbing fastness grades matched the baseline across cotton, nylon, polyester and acrylic components.

  5. Baseline and trial differed in fabric structure, GSM, batch size and shade, so matched trials are needed to confirm scalability.

A carrier-assisted dyeing trial at NAZ Bangladesh Ltd cut peak dyeing temperature by 15°C, from the conventional 130°C to 115°C, and reduced specific steam consumption by 16.7% — from 1.286 to 1.072 kg of steam per kg of fabric. The trial, coordinated by Textile Today and commissioned by HI TECH, ran on 80/20 CVC (cotton/polyester) single jersey fabric with a GSM of 180 and a 42 kg batch weight.

The low-temperature cycle also shortened total process time from 222 minutes to 170 minutes, saving 52 minutes per batch and delivering a calculated productivity gain of 23.4%. The team behind the study lists Sadia Afrin Mou, Anik Naha and Mita Akhter as innovation masterminds, with Khaled Faisal, general manager of NAZ Bangladesh Ltd, supervising on the factory floor and Md. Mesbah Uddin, technical sales manager at Transfar Chemicals, providing technical supervision. Najmus Sakib, senior executive at Textile Today, coordinated the project.

Why polyester normally needs 130°C

Polyester is hydrophobic and highly crystalline, with no functional groups that attract dyestuffs. Conventionally, mills dye it with disperse dyes at 130–140°C, where thermal energy loosens the polymer structure enough for dye molecules to diffuse in. The study cites the work of Burkinshaw (2024), who showed that elevated temperature raises chain mobility and enlarges free volume inside the fibre.

Carriers attack the same barrier chemically. They swell the fibre and lower its effective glass transition temperature, so dye diffuses at 115°C without the full thermal load. A dispersing agent keeps dye particles suspended; a levelling agent spreads dye evenly; acetic acid holds the bath mildly acidic to support exhaustion and fixation.

What did the numbers show?

The study compared a live baseline batch against the trial cycle using heat-balance calculations at a 1:6 liquor ratio, a steam enthalpy of 2,755.5 kJ/kg at 6 bar, and an assumed 36% steam loss (6% distribution, 10% heat exchanger, 20% condensate), leaving 64% useful heat.

  • Energy per kg of fabric fell from 2,267.9 kJ/kg to 1,890.0 kJ/kg — a 16.7% reduction.
  • Steam per batch was 1,405.91 kg for the 1,093.19 kg baseline lot and 45.01 kg for the 42 kg trial lot; per-kg figures give the fair comparison.
  • The trial used direct heating and cooling rather than the baseline's 1.5°C/min gradients, which accounted for much of the 52-minute time saving.
  • Dry and wet rubbing fastness stayed at grades between 4–5 and 2–3 across cotton, nylon, polyester and acrylic components, matching the baseline in every tested cell. Wool was tested only in the trial, with wet rubbing at 4–5.

The dyed trial fabric showed a level, uniform shade with no visible patchiness at the reduced temperature.

How solid is the comparison?

The study's own limitations section flags a significant caveat: the baseline ran on CVC F-Terry fabric at GSM 350 and 1,093.19 kg, while the trial ran on single jersey at GSM 180 and 42 kg. Fabric structure, GSM, batch size and shade all differed, so the authors call for matched industrial trials before scaling. The carrier chemistry, coded TF-258WH, was not disclosed under confidentiality agreements with Transfar Chemicals, which limits how far other mills can replicate the formulation.

The literature base behind the approach is established. Derbyshire documented carrier dyeing near boiling point as early as 1974. More recent work, cited from Pasquet et al. (2013) and Souissi et al. (2021), shows biodegradable carriers such as vanillin and coumarin matching toxic legacy carriers at 100°C — relevant for mills that must answer ZDHC-style chemical compliance questions about carrier toxicity and odour.

What should sourcing and compliance teams take from it?

The operational case is throughput and utilities: fewer steam-kilograms per kg of fabric, more batches per shift, lower boiler fuel demand and reduced effluent load to the ETP. The study maps these gains to SDG 7, 9 and 12. But the buyer-facing claim rests on one unmatched pair of batches and an undisclosed carrier.

Mills considering the switch should commission matched-fabric trials — same GSM, batch size and shade depth — and request the carrier's safety data sheet before approving the formulation, since carrier toxicity remains the compliance weak point of low-temperature polyester dyeing.

via textiletoday.com.bd (Source)

Share this article:

More from Grace Kim

Grace Kim

Show full bio

Correspondent covering regulation, policy and their impact on Light industry and softgoods manufacturing at Softgoods Report.

381 articles